S trap vs P trap: 5 Differences You Need to Know Now (2024)

When we talk about ‘traps’ in bathroom plumbing, we are referring to a particular piping arrangement designed to protect your bathroom from bad sewer odor.

At first glance, it might seem strange to need a specific piping shape.

Indeed the water just needs to be drained away by a straight line.

The shape of the pipe matters a lot because that drain is designed to ‘pool’ a bit of the water, which creates an air-tight seal that prevents dangerous and harmful sewer gasses from making their way back up the system and into your bathroom.

So, we use ‘traps’ to create a water seal that traps these gasses.

Two of the most common trap types we use are called the ‘S trap’ and the ‘P trap.’

The main difference between an S trap and a P strap is their shape.

They are named S and P because their piping shapes loosely resemble the letter they are called after.

While both trap types are fundamentally there to serve the same purpose, their unique shapes make them pool water differentlyand as such, the P-trap is much more effective at stopping these harmful gasses than the S-trap.

In this article, we’ll take an in-depth look at the differences between these two plumbing trap types so you can fully understand why the P trap is preferred over the S trap.

What is an S trap?

Table of Contents

The S trap came before the P trap.

It was a logical shape that could create that pool of water that would make a seal and hold back unwanted gasses from backing up into your bathroom.

This includes gasses like methane, hydrogen sulfide, nitrogen and carbon monoxide, which are dangerous.

You do NOT want these making their way into your bathroom.

The S shape is compact and convenient and has the added benefit of catching any objects that fell down the drain, such as watches or wedding rings, so that they could be easily fished back out.

It seemed ideal, but there was a fundamental flaw in its design.

While simple tasks like washing your hands or a toilet flush were not a problem.

Anytime a large amount of water was flushed down the drain (such as a full sink of water or if a bucket of water was dumped in the toilet), it would create a siphoning vacuum effect that was strong enough to suck excess water from the pool we needed to have sitting in the trap.

This meant that sometimes there was so little water in the trap (we call this leaving the trap ‘dry’ that there was a direct air gap allowing those gasses to seep back into the bathroom.

This was quickly deemed unacceptable and is now considered prohibited throughout the entirety of the United States and in many other countries worldwide.

Older homes found to be using these traps will be required to replace them with the updated P trap design.

What is a P trap?

After the overall failure of the S trap design, some modifications were made to it to address its issues and we were left with what we now call the P trap.

Much like the S trap, it’s named this way as the piping shape resembles that of a P.

The goal is precisely the same as the S trap, to create a small pool of water that ‘traps’ those harmful gasses down in the plumbing and prevents them from entering our home.

Two significant adjustments were made to the S trap for us to arrive at the P trap.

1: Firstly, a ‘vent’ was added to the piping system.

This means as the water is drained down the sink, it also pulls in air from a vent that leads outside.

This air allows the pressure inside the drain to balance itself and dramatically reduces the possibility of water being siphoned out and leaving the trap ‘dry’.

2: A long extension was added (this makes the tail of our ‘P’ shape), reducing the ‘pulling’ aspect that the tighter S shape caused.

This is called a ‘waste arm extension’.

While the P trap is not 100% perfect, there are still certain circumstances in which the water pool can be compromised (for example, through evaporation if you end up not using the sink for a prolonged period).

The chances of experiencing this on a P trap are considerably lower than on an S trap.

It’s also possible to ‘convert’ an older S strap to a P trap by adding an AAV (Air Admittance Valve), the air vent that will help equalize the pressure and that all-important waste arm extension which requires a little extra piping to be added.

This can sometimes be easier than just re-doing the whole plumbing system.

You can even buy S trap to P trap conversion kits to make this process easier.

What are the differences between an S trap and a P trap?

Hopefully, you now know better why the S trap is no longer used and the risks involved with having one installed.

Let’s take a deeper look at these differences so you can better understand how they differ.

1. The shape

Their shape is the most notable difference between the two plumbing trap types.

Both traps take after their respective letter, so the S trap is shaped like an S or snake shape, while the P trap consists of a single curved seal which then extends out into a waste arm extension, just like the letter P.

This arm extension has the added benefit of allowing the water to drain while air is taken in through the vent equalizing the pressure.

This P shape, in turn, directly counteracts the siphoning issue that the S trap runs into.

The S shape by itself does fundamentally work under many use-case scenarios.

Itis more prone to having its water siphoned off when large amounts of water have to be drained away.

In conclusion, the P shape is much more effective than the S shape.

2. The use of a vent

When S traps were first invented in 1775, they were used for over 100 years until Thomas Crapper invented the U-bend (another term for the P crack) in 1880.

At this time, less thought was put into health and safety, and the consequences of those harmful gasses were not fully understood.

A big factor that makes the P trap superior to the S trap is the use of a vent.

While the P trap introduced the waste arm extension to help reduce the siphoning effect and increase the reliability of the trap.

That alone was not enough.

So we also introduced a vent allowingoutside air to be pulled into the drain as the water flows away.

This reduced (or equalized) the pressure within the system and dramatically reduced the chance of excess pressure sucking that all-important trap water away.

Nowadays, a vent is a mandatory part of the plumbing code and almost all modern homes will have one.

3. Volume of water used

Another aspect to consider is the volume of water used when flushing or draining.

Generally speaking, an S trap requires a large volume of water to drain the waste and refill the trap.

This is because of the siphoning effect and the shape.

The P trap, on the other hand, thanks to the addition of the vent, equalizes the pressure as soon as the waste is removed, meaning no excess water is siphoned down the drain, which therefore means less water is needed to keep the trap filled.

4. Plumbing code standards

Because of its inherent design flaws and risk of going dry, resulting in harmful gasses backing into your bathroom, S traps have slowly been phased out of new builds.

They are illegal to install in many countries.

Almost all new constructions will use the P trap as it’s up to code and far safer than the S trap.

S traps can still be purchased and aren’t illegal to buy, but by installing one, you are breaking the plumbing codeand if you are caught, you will either need to replace it with a P trap or use a mod kid to turn it into a P trap.

5. Size

At first glance, it might seem like the S trap has a smaller footprint in your bathroom due to its tight snake-like shape and the fact a P trap has that long waste arm coming out from it.

But in fact, it’s the opposite way around. Because the S trap needs to conserve water in the sink to function, the piping is made larger to accommodate this.

Whereas the P trap doesn’t need to do this and can get away with holding far less water and, as such, uses thinner piping, leaving a smaller footprint than that of the S trap.

S trap vs. P trap: Are they the same?

Regardless of what shape piping you use, traps are all designed to do the same thing, prevent harmful gasses and foul odors from backing up into our bathroom.

We delineate the twoin their effectiveness at doing this job.

The S trap is inherently flawed as a suctioning effect can pull the water out, leaving it ‘dry’.

This means there is no complete seal and an air gap allows those gasses back up to the bathroom.

These traps are now illegal in most places and should be replaced with a P trap which does a far better job trapping those harmful gasses.

  • As the names might suggest, the S trap is shaped like an S, whereas the P trap is shaped like a P.
  • The P trap uses a vent that helps equalize the air pressure, thus reducing the chance of water being pulled out of the trap.
  • The S trap requires a larger volume of water to operate, whereas the P trap is more efficient and better at conserving water.
  • The S trap does not meet modern plumbing code standards and is illegal in many countries. The P is the current most common choice for most installations.
  • The P trap is smaller in size than the S trap.

Related Article:J-Bend VS P-Trap

5/5 - (6 votes)

David Kessler( Licensed Contractor )

David Kessler is a CSLB licensed contractor with over 25 years of experience. He is specialized in home building, construction, and electrical works; he also has a keen eye for interior design and, over the years, has collaborated with various architects.

S trap vs P trap: 5 Differences You Need to Know Now (2024)

FAQs

S trap vs P trap: 5 Differences You Need to Know Now? ›

An S-trap flows down from the drain, curves up, then curves back down. The P-trap also flows down from the drain and curves, but the curve finishes on a horizontal pipe that takes the waste out. Once the trap dries out, sewer gases can start flowing back into your home.

Why is s-trap illegal? ›

The “s” design could cause a water siphon, removing the water built up in the curve, opening the seal, and allowing sewer gas to pass through. This flaw is whys-traps are no longer allowed in plumbing code and should be replaced if you have one.

What are the advantages of an S trap? ›

The smooth interior won't cause buildup or bad odors. The trap's 1-1/4 inch inlet adapts to 1 1/4″ sink drains. The S trap design is not only space-saving but also less cleanout and won't clog. The floor-mounted installation type has a flange for connection to the floor.

What is the difference between a running trap and a P-trap? ›

Our traps are manufactured using food-grade stainless steel, and are recommended for use with all FoodSafe Catch basins: P-Trap for any vertical/bottom outlet connections, and Running Trap for horizontal/side outlet connections.

How do I know if my toilet is S-trap or P-trap? ›

Therefore, what is the difference between these two traps? An S-trap is an S-shaped trap between the toilet outlet and the sewer system. It is connected to the drainpipe through the floor. On the other hand, a P-trap is shaped like the letter P and is connected to the drainage system through an opening in the wall.

What are the disadvantages of the S-trap? ›

While S traps were once popular, especially for ground floor installations due to their specific design and water flow characteristics, they have some significant drawbacks: They can be prone to siphoning, which means the water seal can be lost, allowing sewer gases to enter the home.

Can you replace an S-trap with a P-trap? ›

P-traps can be used for plumbing that exits through both the wall and the floor, making them usable for any plumbing fixture. There may be some difficulty in replacing your old S-trap to a P-trap so it would be advisable to seek professional help before taking on the replacement yourself.

Do all sinks need an AP trap? ›

The trap is employed in any plumbing system that uses a drain and accepts sanitary waste from tubs, showers and sinks.

How do I know if I have a P-trap? ›

The P-trap is the P-shaped section of pipe in the line that runs from the bottom of your sink to the wall.

Why is it called an S-trap? ›

A common plumbing defect often found under sinks, in older and remolded homes, is the presence of S-traps. These plumbing traps are shaped like an “S” laying on its side.

References

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Chrissy Homenick

Last Updated:

Views: 5533

Rating: 4.3 / 5 (74 voted)

Reviews: 89% of readers found this page helpful

Author information

Name: Chrissy Homenick

Birthday: 2001-10-22

Address: 611 Kuhn Oval, Feltonbury, NY 02783-3818

Phone: +96619177651654

Job: Mining Representative

Hobby: amateur radio, Sculling, Knife making, Gardening, Watching movies, Gunsmithing, Video gaming

Introduction: My name is Chrissy Homenick, I am a tender, funny, determined, tender, glorious, fancy, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.